Free PDF Ebook | FileMount.com

… ANGLE TPMS SENSOR MANUAL MOUNTING GUIDELINES Hyundai/Kia design. Ref N° … TPMS SENSOR SERVICE GUIDELINES. FIXED ANGLE TPMS SENSOR. MANUAL MOUNTING. GUIDELINES …

More PDF Content

FIXED ANGLE TPMS SENSOR MANUAL MOUNTING GUIDELINES Hyundai/Kia design 1 FIXED ANGLE TPMS SENSOR MANUAL MOUNTING GUIDELINES Hyundai/Kia design Ref N : 00051-00010-PCE-h Date : 07 September 25 th TPMS SENSOR SERVICE GUIDELINES FIXED ANGLE TPMS SENSOR MANUAL MOUNTING GUIDELINES Hyundai/Kia design 2 FIXED ANGLE TPMS SENSOR MANUAL MOUNTING GUIDELINES Hyundai/Kia design Ref N : 00051-00010-PCE-h Date : 07 September 25 th TPMS SENSOR SERVICE GUIDELINES SCOPE AND SUMMARY: This document outlines the guidelines for the manual mounting on the rim of EnTire/TRW fixed angle TPM sensors.This document does not cover any other TPM sensors. – Sensor & valve components
Page 3
- Step 1 Start fitting the valve unit on the rim
Page 4
- Step 2 Tighten the nut
Page 5
- Step 3 Check the assembly sensor  valve  rim
Page 6
3 FIXED ANGLE TPMS SENSOR MANUAL MOUNTING GUIDELINES Hyundai/Kia design Ref N : 00051-00010-PCE-h Date : 07 September 25 th TPMS SENSOR SERVICE GUIDELINES Sensor & valve components Sensor-valve Rubber grommet Valve stem ValveCap nut Rubber grommet Valve stem ValveCap nut 4 FIXED ANGLE TPMS SENSOR MANUAL MOUNTING GUIDELINES Hyundai/Kia design Ref N : 00051-00010-PCE-h Date : 07 September 25 th TPMS SENSOR SERVICE GUIDELINES Step 1 : Start fitting the sensor – valve unit on the rim Slide the sensor-valve unit through the valve hole of the rim. Hold the sensor against the rim and the rubber grommet against the sealing surface. Insert the nut over the valve stem. Start tightening the nut using a 12 mm deep socket. 5 FIXED ANGLE TPMS SENSOR MANUAL MOUNTING GUIDELINES Hyundai/Kia design Ref N : 00051-00010-PCE-h Date : 07 September 25 th TPMS SENSOR SERVICE GUIDELINES Step 2 : Tighten the nut Important :Tighten slowly with quarter turn steps until the final torque is reached. Continue tightening the nut until contact with the rim and then tighten to the final torque.The recommended torque setting is 4.0 Nm (35,5 lbf.in). For example, this allows the final torque to be between 3.5 to 4.5 Nm if a +/- 12 % tolerance torque wrench is used. (Note : it is recommended to use a class B tool but a class C tool is acceptable) The standard recommended torque range is given by the ETRTO, TRA for a rubber corner joint valve. Dispersion with +/- 12% tolerance (example)Standards recommended rangeOut of range 4.5 3.5 4.0 5.0 3.0 (Nm) 0 Nut manual tightening Torque 40 31 35,5 44 26,5 (lbf.in) 0 6 FIXED ANGLE TPMS SENSOR MANUAL MOUNTING GUIDELINES Hyundai/Kia design Ref N : 00051-00010-PCE-h Date : 07 September 25 th TPMS SENSOR SERVICE GUIDELINES Step 3 : Check the assembly sensor-valve – rim Check that the valve is firmly attached to the rim and that the sensor is firmly attached to the valve. Final positioning of the sensor feet is dependent on the wheel dimensions and may not be uniform.Possibilities are neither foot, one foot or both feet may contact the wheel drop center. WARNING : Risk of damage during the tire mounting / dismounting if the sensor is not firmly attached to the rim.